This website uses cookies to ensure you get the best experience on our website. Read more
BENDER REBAR
In stock
Only 1 left
SKU
ALBA-D36L
TTD $58,489.05
Alba manufactures three models of lightweight benders: D36L; D42L and D52L. All of these can be supplied with an optional programmer.
The D36L model comes in a version with a single-phase motor.
The main technical characteristics of lightweight benders are:
Turntable forward and reverse rotation: The table can turn in two directions of operation.
Angles selector: Desired angle is obtained by inserting the pin in the bending table periphery.
Two drive systems: Automatic and continuous for spirals.
Remote control of lightweight benders by pedal.
Electric board: In monoblock; sealed case -Low voltage (48 V)- With emergency stop as per CE Standards.
Fitted with brake-motor.
Swing square: With complete equipment of bending bushes and bolts.
Special attachments: stirrups; spirals; etc.
Turn table of big diameter: 375 mm (D36L & D42L) / 445 mm (D52L)-With 9 bending holes-With possibility to change point ô0ö. (D36L; D42L & D52L).
Gathering tray: At the bottom; to keep pedal; bolts; bushes; tools; etc.
Bending Guard: Safety system that prevents the access to the bending area during the turning of the plate.
The D36L model comes in a version with a single-phase motor.
The main technical characteristics of lightweight benders are:
Turntable forward and reverse rotation: The table can turn in two directions of operation.
Angles selector: Desired angle is obtained by inserting the pin in the bending table periphery.
Two drive systems: Automatic and continuous for spirals.
Remote control of lightweight benders by pedal.
Electric board: In monoblock; sealed case -Low voltage (48 V)- With emergency stop as per CE Standards.
Fitted with brake-motor.
Swing square: With complete equipment of bending bushes and bolts.
Special attachments: stirrups; spirals; etc.
Turn table of big diameter: 375 mm (D36L & D42L) / 445 mm (D52L)-With 9 bending holes-With possibility to change point ô0ö. (D36L; D42L & D52L).
Gathering tray: At the bottom; to keep pedal; bolts; bushes; tools; etc.
Bending Guard: Safety system that prevents the access to the bending area during the turning of the plate.
Alba manufactures three models of lightweight benders: D36L; D42L and D52L. All of these can be supplied with an optional programmer.
The D36L model comes in a version with a single-phase motor.
The main technical characteristics of lightweight benders are:
Turntable forward and reverse rotation: The table can turn in two directions of operation.
Angles selector: Desired angle is obtained by inserting the pin in the bending table periphery.
Two drive systems: Automatic and continuous for spirals.
Remote control of lightweight benders by pedal.
Electric board: In monoblock; sealed case -Low voltage (48 V)- With emergency stop as per CE Standards.
Fitted with brake-motor.
Swing square: With complete equipment of bending bushes and bolts.
Special attachments: stirrups; spirals; etc.
Turn table of big diameter: 375 mm (D36L & D42L) / 445 mm (D52L)-With 9 bending holes-With possibility to change point ô0ö. (D36L; D42L & D52L).
Gathering tray: At the bottom; to keep pedal; bolts; bushes; tools; etc.
Bending Guard: Safety system that prevents the access to the bending area during the turning of the plate.
The D36L model comes in a version with a single-phase motor.
The main technical characteristics of lightweight benders are:
Turntable forward and reverse rotation: The table can turn in two directions of operation.
Angles selector: Desired angle is obtained by inserting the pin in the bending table periphery.
Two drive systems: Automatic and continuous for spirals.
Remote control of lightweight benders by pedal.
Electric board: In monoblock; sealed case -Low voltage (48 V)- With emergency stop as per CE Standards.
Fitted with brake-motor.
Swing square: With complete equipment of bending bushes and bolts.
Special attachments: stirrups; spirals; etc.
Turn table of big diameter: 375 mm (D36L & D42L) / 445 mm (D52L)-With 9 bending holes-With possibility to change point ô0ö. (D36L; D42L & D52L).
Gathering tray: At the bottom; to keep pedal; bolts; bushes; tools; etc.
Bending Guard: Safety system that prevents the access to the bending area during the turning of the plate.
| SKU | ALBA-D36L |
|---|---|
| Weight | 0.000000 |
| Manufacturer | ALBA |
Write Your Own Review
The attribute color not support show on frontend please choose another attribute.
- Latest Products
